What size socket or wrench is needed?

You at least need a set of 3/8″ (drive size) sockets set with sizes 8-19mm. Some vehicles use Allen or Torx bits for the caliper guide pins. Torx and Allen bits are not interchangeable. The wrong bit may feel like it fits, but it might damage the female head of the bolt.

What size drill bit is 10mm?

There are variations for a 10mm tap. The 10mm x 1.0 uses a 9.1mm metric drill bit and the 10mm x 1.5 uses a 8.7mm metric drill bit. As you can see by the chart, there are many different sizes of 10mm taps and the exact size depends on the drill bit you should use.

What is the standard socket size?

• 5mm: Used on fixing inner fender screws and most interior screws.
• 7mm: Used for bumper bolts, windshields, hood bolts, and seat belts
• 10mm: The most common for fender bolts, license plates, and antennas.
• 13mm: Used for bracket bolts
• 15mm: Used to fix larger bumper brackets and fog lights, infill panels, and doors in the home

What are the most common socket sizes?

⅜-inch drive size sockets are the most common and most available. ¼-inch drive size sockets are ideal when you are in tight spaces or when you are working with recessed nuts. What is the most common socket? 10mm sockets and 36mm sockets are typically the most commonly used sizes.

Is a 3/8 socket the same as a 10mm?

8mm = 5/16 inch. 9mm = almost 3/8 inch. 10mm = just over 3/8 inch.

What size bolt fits a 10mm socket?

Metric Fasteners – Wrench size needed for Driving common NutsScrew SizeWrench Size *Alt Size, Acorn ***M58mm8mmM610mm10mmM813mm13mm8 more rows

Can you use 3/8 on a 10mm socket?

A: Hey Ed, Absolutely, as long as the torque wrench is 3/8 in. drive. You shouldn’t have any issues with out sockets breaking at any torque range on their respective torque wrenches. We make sure all far exceed ANSI specifications for their given size.

Is M10 a 10mm?

Steel bolt with M10 metric thread. Metric threads are designated with a capital M plus an indication to their nominal outer diameter and their pitch: This bolt is M10 x 1.5 – which means the outside diameter is 10mm and the threads are 1.5mm apart (the most common thread pitch for M10).

Why is there no 10mm socket?

It seems like the 10mm bolt size is the most common bolt size across most cars so, naturally, you’re going to use the 10mm socket the most. But, since the 10mm socket is so small, if you don’t remember where you place it, this is the socket you’ll most likely lose, hence all the memes.

What can I use for a 10mm bolt?

Metric hex bolts, 10mm x 100mmStainless steel 18-8 (A-2) Also known as A-2 stainless, 18-8 is the most common grade of stainless steel for general use.Stainless steel 316 (A-4) … Zinc plated class 8.8 steel. … Zinc plated class 10.9 steel.

What size wrench fits a M10 nut?

ResourcesWRENCH OR SOCKET SIZE ACROSS FLATSHEX NUTS STYLE 1HEAVY HEX NUTS13.00M8 x 1.25 15.00M10 x 1.5 16.00M10 x 1.5 18.00M12 x 1.75 36 more rows

What size bolt has a 10mm head?

The standard 6mm cap screw has a 10mm head.

What size bolt uses a 10 mm nut?

Spanner and Allen Key SizesSizeSpannerAllen KeyM58 mm4 mmM610 mm5 mmM813 mm6 mmM1017 mm8 mm5 more rows

Is M8 a 10mm?

So an M8 bolt would have a shaft diameter that’s slightly under 8mm which means that the bolt should fit through an 8mm hole.

Is the M6 a 10mm?

M6 (6mm x 10mm) Hex Socket Cap Screw (Bolt) – Steel (Pack of 20)

What is the size of a 33mm socket?

A 33mm metric socket is 1.29921 inches in size which most closely matches a 1 5/16 standard size socket. A 1 5/16 standard size socket is 33.34mm which is a little bit bigger than a 33mm socket but it is the standard size socket that best fits over a 33mm bolt.

What is the difference between standard sockets and metric sockets?

Standard sockets are measured in inches while metric sockets are measured in milimeters (mm). Depending on the region you live in, one measurement system will be more common than the other. This can become frustrating because different manufacturers also embrace different measurement systems.

What is a 36 mm in standard size?

A 36mm socket is 1 7/16″ in standard (SAE) size, almost. 1 7/16″ converts into so a 1 7/16 socket is the standard socket that best fits a 36mm fastener.

Do metric sockets match standard sockets?

Some metric sockets, like the 32mm socket, do match exactly with a standard sized socket so you see why switching between the two systems can be frustrating. Some fit, some don’t, and remembering what fits what can be difficult. Tip: Keep your sockets neatly organized from smallest to largest so that you can quickly test fit alternate sizes.

What is 10mm socket?

10 MM is one of those ‘b*stard’ size sockets that no SAE equivalent exists, at least going by 1/16″ gradients. Something odd, if it even exists, would be 13/32″ as close as I can figure, 12/32″ is 3/8″ and 14/32″ would be 7/16″, 10 MM falls in between the latter two ‘32’ fractions if an inch.

What size driver for a 10mm socket?

A 10mm socket, either conventional or long socket could be driven by a 1/4 inch square driver, or a 3/8 inch square driver.

How to determine the size of a driver?

The size driver would be determined by the bolt hardness , and the amont of torque available to exert on to the bolt.

What size is a M6 bolt?

if you mean the nut or bolt size? it is M6 (6 mm diameter) the nut and bolt head is 10 mm across the flats.

Is 10mm a metric?

Well, this is kinda tough…10mm is a regular size only metric.

Is 10mm a regular size?

However, if you mean what imperial/USCU size is equivalent, there is none. 10 mm is very much regular.

Can you use a SAE socket on a metric bolt head?

But to use a SAE socket on a ‘metric bolt head’ will round off the edges, since two much force will be distributed over too small an area of the bolt.

What are the different sizes of sockets?

Sockets follow two different sizes. There are SAE-sized sockets and metric sockets. The sizes are often used interchangeably. Knowing about both is important if you need to use your sockets regularly.

What is the most common socket?

If you’re new to using sockets, point sockets are the way to go. The most common point socket is the 12-point socket. The biggest benefit of the 12-point socket is that it’s easy to use. Simply slip the socket over any of the 12 positions and you’re set.

Why Do You Need Socket Sets?

Sockets are generally used to tighten or loosen different fasteners. They can be an alternative to the conventional wrench if you know their usage. Most DIY enthusiasts and mechanics prefer having a set handy.

Why do you need multiple sockets?

One of the main benefits of having a socket set is versatility. If you’re dealing with a tight fastener, having multiple sockets can be beneficial. Also, it provides better grip when compared to wrenches.

Why are point sockets so expensive?

Point sockets are slightly more expensive than regular ones. Mostly due to the fact that they’re available in a lot of sizes together. If you’re planning to spend, point sockets are a good idea.

How many types of sockets are there?

Now that we’ve discussed the types of socket drives, let’s discuss the types of sockets. There are two common types of sockets available. The use of sockets has changed a lot over the years.

What is the drive on a socket?

The drive is the main part of the socket. It is the hole where the socket is attached to a turning tool. Like a wrench or a ratchet. The type of drive depends on the task at hand.

Why is a 6 point socket better than a 12 point socket?

It is thought a six-point socket will be more durable than a 12-point because its inner walls are set against all six sides of the hardware.

What is a 12 point socket?

A 12-point socket is convenient and easy to use. You can slip it over the hardware in any one of 12 positions, which makes it easier to align.

What is the drive on a socket wrench?

The drive on your socket wrench is the square section sitting on the ratchet. Certain sizes accept a varying number of sockets that can be either metric and SAE.

What are some examples of impact sockets?

Impact sockets are made in such a way they work with these other tools. A prime example is an electric or pneumatic impact wrench. If you use these, you will need a socket sets built to withstand these higher torques.

What size drive is used for low torque?

1/4” Drives: You find these used for low-torque work and are usually for smaller sized sockets possibly up to around 14mm as a maximum.

Can you use the conversion chart to check your socket size?

You can quickly use the conversion chart to check your metric socket size against your SAE socket size and vice versa.

Can you use different sizes of sockets?

While you have a large number of metric and SAE standard socket size, you can have differing wrenches to use these.