What size socket or wrench is needed?

You at least need a set of 3/8″ (drive size) sockets set with sizes 8-19mm. Some vehicles use Allen or Torx bits for the caliper guide pins. Torx and Allen bits are not interchangeable. The wrong bit may feel like it fits, but it might damage the female head of the bolt.

What size drill bit is 10mm?

There are variations for a 10mm tap. The 10mm x 1.0 uses a 9.1mm metric drill bit and the 10mm x 1.5 uses a 8.7mm metric drill bit. As you can see by the chart, there are many different sizes of 10mm taps and the exact size depends on the drill bit you should use.

What is the standard socket size?

• 5mm: Used on fixing inner fender screws and most interior screws.
• 7mm: Used for bumper bolts, windshields, hood bolts, and seat belts
• 10mm: The most common for fender bolts, license plates, and antennas.
• 13mm: Used for bracket bolts
• 15mm: Used to fix larger bumper brackets and fog lights, infill panels, and doors in the home

What are the most common socket sizes?

⅜-inch drive size sockets are the most common and most available. ¼-inch drive size sockets are ideal when you are in tight spaces or when you are working with recessed nuts. What is the most common socket? 10mm sockets and 36mm sockets are typically the most commonly used sizes.

Is a 3/8 socket the same as a 10mm?

8mm = 5/16 inch. 9mm = almost 3/8 inch. 10mm = just over 3/8 inch.

What is equivalent to a 10 mm socket?

3/16″Metric / Standard Wrench Conversion ChartBolt DiameterMetricStandard3/16″10mm3/8″1/4″11mm7/16″5/16″13mm1/2″3/8″14mm9/16″39 more rows•Apr 9, 2020

What is a 10mm in standard?

10mm. Little over 3/8 Inch. 0.39370 Inches. 11mm. 7/16 Inch.

What size socket fits a 10mm bolt?

Metric Fasteners – Wrench size needed for Driving common NutsScrew SizeWrench Size *Alt Size, Acorn ***M58mm8mmM610mm10mmM813mm13mm8 more rows

What size is a 10mm nut?

A: This product is 10mm in thread size, 0.4375 in (11mm) in height. Part# 801736, 1/4 in. -20 Zinc Plated Hex Nut, is about 5mm thick. Helpful?

Is M10 same as 10mm?

If the size is M10 x 25, that would mean that the diameter is 10 mm. Since there is no thread pitch listed, the fastener is assumed to have a coarse thread. The 25 indicated a length of 25 mm. A matching nut would be labeled M10, which also doesn’t require a thread pitch since it’s a course thread fastener.

What is 10mm in diameter?

Pistol cartridgesName (mm/in)Bullet diameterCase length.40 S&W10.16 (.400)21.59 (.850).40 Super10.16 (.400)25.20 (.992)10mm Auto10.16 (.400)25.20 (.992)10mm Magnum10.16 (.400)31.88 (1.255)3 more rows

What socket is M10 bolt?

BUTTON HEAD SOCKET CAP SCREW – METRICSizeHead DiameterHexagon Socket SizeM6-1.010.504.00M8-1.2514.005.00M10-1.5017.506.00M12-1.7521.008.003 more rows

What size wrench fits a M10 nut?

ResourcesWRENCH OR SOCKET SIZE ACROSS FLATSHEX NUTS STYLE 1HEAVY HEX NUTS13.00M8 x 1.25 15.00M10 x 1.5 16.00M10 x 1.5 18.00M12 x 1.75 36 more rows

What metric bolt has a 10 mm head?

Metric Shoulder Bolt DimensionsShoulder Diameter (A)Thread (C)Head Height (F)8mm6mm x 1.05.5mm10mm8mm x 1.257mm12mm10mm x 1.59mm16mm12mm x 1.7511mm3 more rows

What size wrench fits a M10 nut?

ResourcesWRENCH OR SOCKET SIZE ACROSS FLATSHEX NUTS STYLE 1HEAVY HEX NUTS13.00M8 x 1.25 15.00M10 x 1.5 16.00M10 x 1.5 18.00M12 x 1.75 36 more rows

What socket is M10 bolt?

BUTTON HEAD SOCKET CAP SCREW – METRICSizeHead DiameterHexagon Socket SizeM6-1.010.504.00M8-1.2514.005.00M10-1.5017.506.00M12-1.7521.008.003 more rows

What is the diameter of a 10mm bullet?

10.17 mm10mm AutoBullet diameterC.I.P.: 10.17 mm (0.400 in) SAAMI: .4005 in (10.17 mm)Neck diameterC.I.P.: 10.74 mm (0.423 in) SAAMI: .423 in (10.7 mm)Base diameterC.I.P.: 10.80 mm (0.425 in) SAAMI: .425 in (10.8 mm)Rim diameterC.I.P.: 10.80 mm (0.425 in) SAAMI: .425 in (10.8 mm)26 more rows

What is the size of a 33mm socket?

A 33mm metric socket is 1.29921 inches in size which most closely matches a 1 5/16 standard size socket. A 1 5/16 standard size socket is 33.34mm which is a little bit bigger than a 33mm socket but it is the standard size socket that best fits over a 33mm bolt.

What is the difference between standard sockets and metric sockets?

Standard sockets are measured in inches while metric sockets are measured in milimeters (mm). Depending on the region you live in, one measurement system will be more common than the other. This can become frustrating because different manufacturers also embrace different measurement systems.

What is a 36 mm in standard size?

A 36mm socket is 1 7/16″ in standard (SAE) size, almost. 1 7/16″ converts into so a 1 7/16 socket is the standard socket that best fits a 36mm fastener.

Do metric sockets match standard sockets?

Some metric sockets, like the 32mm socket, do match exactly with a standard sized socket so you see why switching between the two systems can be frustrating. Some fit, some don’t, and remembering what fits what can be difficult. Tip: Keep your sockets neatly organized from smallest to largest so that you can quickly test fit alternate sizes.

What is 10mm socket?

10 MM is one of those ‘b*stard’ size sockets that no SAE equivalent exists, at least going by 1/16″ gradients. Something odd, if it even exists, would be 13/32″ as close as I can figure, 12/32″ is 3/8″ and 14/32″ would be 7/16″, 10 MM falls in between the latter two ‘32’ fractions if an inch.

What size driver for a 10mm socket?

A 10mm socket, either conventional or long socket could be driven by a 1/4 inch square driver, or a 3/8 inch square driver.

How to determine the size of a driver?

The size driver would be determined by the bolt hardness , and the amont of torque available to exert on to the bolt.

What size is a M6 bolt?

if you mean the nut or bolt size? it is M6 (6 mm diameter) the nut and bolt head is 10 mm across the flats.

Is 10mm a metric?

Well, this is kinda tough…10mm is a regular size only metric.

Is 10mm a regular size?

However, if you mean what imperial/USCU size is equivalent, there is none. 10 mm is very much regular.

Can you use a SAE socket on a metric bolt head?

But to use a SAE socket on a ‘metric bolt head’ will round off the edges, since two much force will be distributed over too small an area of the bolt.

What are the different sizes of sockets?

Sockets follow two different sizes. There are SAE-sized sockets and metric sockets. The sizes are often used interchangeably. Knowing about both is important if you need to use your sockets regularly.

What is the most common socket?

If you’re new to using sockets, point sockets are the way to go. The most common point socket is the 12-point socket. The biggest benefit of the 12-point socket is that it’s easy to use. Simply slip the socket over any of the 12 positions and you’re set.

Why Do You Need Socket Sets?

Sockets are generally used to tighten or loosen different fasteners. They can be an alternative to the conventional wrench if you know their usage. Most DIY enthusiasts and mechanics prefer having a set handy.

Why do you need multiple sockets?

One of the main benefits of having a socket set is versatility. If you’re dealing with a tight fastener, having multiple sockets can be beneficial. Also, it provides better grip when compared to wrenches.

Why are point sockets so expensive?

Point sockets are slightly more expensive than regular ones. Mostly due to the fact that they’re available in a lot of sizes together. If you’re planning to spend, point sockets are a good idea.

How many types of sockets are there?

Now that we’ve discussed the types of socket drives, let’s discuss the types of sockets. There are two common types of sockets available. The use of sockets has changed a lot over the years.

What is the drive on a socket?

The drive is the main part of the socket. It is the hole where the socket is attached to a turning tool. Like a wrench or a ratchet. The type of drive depends on the task at hand.